Request RF6 Aircraft Here

Boof69

Well-known member
Yes sir. The landing gear and the canopy are always separate items. Whether it be Knife Edge or amateur models.
So step one is removing them in the physics editor.
Then add a "Detachable Item" and add the landing gear to it.
Add another detachable item and add the canopy to it.
Place the detachable Items in their respective positions
Under "Software Radio" add an "Output Channel"
Right click on the new Output channel and under "Add" Select "Add Simple Input Feed"
Click on "Input"
In the right hand pane Select "Input channel 6 (Channel 6)"(This is the knob on the interlink)
Now Under "Electronics" right click and add a servo and name in anything you like.
Select it and in the right hand pane select select the output channel you just created.
Now go back to the detachable items you created
In the drop down next to "Detachment Servo" Select the servo you made.
Do this for both detachables.
That's it!
Now when you wish you can rotate the knob and the skids and canopy will fall away.
They will however remain off of the aircraft until the next reset.
 

cbrkhan

New member
Yes sir. The landing gear and the canopy are always separate items. Whether it be Knife Edge or amateur models.
So step one is removing them in the physics editor.
Then add a "Detachable Item" and add the landing gear to it.
Add another detachable item and add the canopy to it.
Place the detachable Items in their respective positions
Under "Software Radio" add an "Output Channel"
Right click on the new Output channel and under "Add" Select "Add Simple Input Feed"
Click on "Input"
In the right hand pane Select "Input channel 6 (Channel 6)"(This is the knob on the interlink)
Now Under "Electronics" right click and add a servo and name in anything you like.
Select it and in the right hand pane select select the output channel you just created.
Now go back to the detachable items you created
In the drop down next to "Detachment Servo" Select the servo you made.
Do this for both detachables.
That's it!
Now when you wish you can rotate the knob and the skids and canopy will fall away.
They will however remain off of the aircraft until the next reset.


Boof69 - Thanks for the detailed information. I have been using real flight for quite a while but this would be my first attempt to modify a model so pardon my inexperience. Question for you

I have looked everywhere in real flight 6.5 specifically in Edit Aircraft Menus... I can’t seem to find "physics editor". Is there a separate tool that I need to perform this action?
 

abaser

Well-known member
Aircraft editor is what he means. To display all options, set the display I believe to advanced.
 

cbrkhan

New member
Boof69 - Thanks for the detailed information. I have been using real flight for quite a while but this would be my first attempt to modify a model so pardon my inexperience. Question for you

I have looked everywhere in real flight 6.5 specifically in Edit Aircraft Menus... I can’t seem to find "physics editor". Is there a separate tool that I need to perform this action?

So I tried modding Synergy E7 using the advance view. Result was junk, I must be doing something wrong ..... Model just disintegrates at spool up. Can someone make and share such a E7 for RF6.5?
 

Boof69

Well-known member
Make sure the knob is turned to the neutral position then once in the air rotate it to release the components.
 

cbrkhan

New member
Make sure the knob is turned to the neutral position then once in the air rotate it to release the components.


I tried the knob at neutral position, still disintegrates at spool up.

There is help here for RF6.5 but with my experience level, I am not getting anywhere. You think If I upgraded to RF 7 , I will get more help?

The reason I don’t upgrade is, I have not seen a heli megapack in RF7. All I fly is helis
 

Coleandrachel

New member
F-22 Raptor

Does anyone know where I can download a decent F-22 Raptor? I keep seeing variations of them, but not the actual aircraft. I'd like to not have to buy an expansion pack. I'm new to this whole thing so I hope I am going about this the right way.

Thanks,
Cole W.
 

csgill75

Well-known member
Does anyone know where I can download a decent F-22 Raptor? I keep seeing variations of them, but not the actual aircraft. I'd like to not have to buy an expansion pack. I'm new to this whole thing so I hope I am going about this the right way.

Thanks,
Cole W.
You will need to buy the expansion pack 3 to get the F-22. There is no other way to get it unless someone creates their own.
 
Last edited:

Maj. Numbskully

Well-known member
Coleandrachal
I"ll Be blunt No Offence as that was your first post and as such so you can understand what youre asking for... but I'll honest......
Very few...ok basicaly none of the talent here want to invest.... nore have the desire
To spend a min of 50-100 hours of thier free time
Researching .. guessing what you mean by "The real thing"......modeling and setting pivots.. writ'in hierarchy. Uv unwrapping or mapping and making the Visable classic CS ...do the bump mapping and specular mapping and then making both the normals file and specular file from both of those and then import into a plug in to export into a flie that RF can import to begin doing the physics model ... for something that already exisits that they them selves have already most likely paid for and already own
JUST so YOU can SAVE a few BUCKS:eek: .....did you really expect that ?

No thats not the way to go about it here...

Not with out krispy kreams anyway

actualy all the really talented modelers here got thier start making something no one else wanted tomake for them
 
Last edited:

csgill75

Well-known member
Hi - does anyone know if there's an Align Speed 700 fuse out for RF 6.5?
The only Heli that I have seen that comes close is the Minicopter Diablo S but it is for RF7. An entire Heli model would have to be created not just a fuselage. Not many people and no Heli modelers that I know of create content for 6.5 anymore as there is more headroom for bigger and better models now only in RF7/RF7.5.

You should get the RF7 upgrade.
 
Last edited:

D3VITZ

New member
Antonov 225

Please put all requests for RF6 aircraft in this thread. Modelers like me prefer to look in one thread for request ideas. When people make their own standalone request threads, they get lost over time when the request isn't immediately picked up. Considering how long it takes to make a model for RF, most requests don't get picked up immediately.

Please provide 3-views, specs, and other reference pictures with your request. This will greatly improve your chances of getting a modeler's attention.
Please, can you make the bigger plane ever made Antonov 225 (for information go to this web page: http://it.wikipedia.org/wiki/Antonov_An-225_Mriya)?
 

PonyMan

New member
This looks like a fun project. I may agree (tentatively) to make this in the near future.
If your refering to my request Boof, I'll gladly help in any way I can. No hurry from my end. After watching your youtube videos I know it takes time to create these things! Thanks
 
Last edited:
Top